X
  • No products in the list

SUPERLOK NORTH AMERICA · METAL SEAL JOINTS

Face Seal Gaskets: Material, Reuse and Torque

What the metal gasket in a face seal joint is made of, when to fit a new one, and how the joint is made up.

5head sizes on the Superlok® UHP gasket page, 1/8 in. to 1 in.
316stainless steel, as listed on that page
1/8 turnpast finger-tight for stainless steel and nickel gaskets (Swagelok®)

A face seal gasket is the part that makes a metal-to-metal joint seal, and it is also the part you choose, fit and decide whether to reuse each time the joint is opened. According to Swagelok®, a manufacturer of metal gasket face seal fittings, its catalog offers gaskets in nickel, 316L stainless steel and copper, and the choice sets the temperature ceiling. This post is for the technician holding the gasket. The joint around it, the glands and nuts of our metal seal fittings, is covered on its own page.

NiNICKEL
SSSTAINLESS STEEL
AgSILVER PLATED
Ret.RETAINER STYLE

Face Seal Gasket Materials: Nickel, Stainless Steel, Silver Plated

In this joint the gasket is the part that is squeezed as the nut is tightened. Material choice trades temperature, plating and the metal the line is made of. The table lists what Swagelok® states for its VCR® gaskets. These are another manufacturer’s figures for its own parts and are shown only so you know what a material choice looks like.

Gasket material, as published by Swagelok®VCR® catalog, MS-01-24, Rev X
Material Stated maximum temperature Notes in the catalog
Nickel 600°F (315°C) A 1/4 in. nickel gasket page lists silver plating
316L stainless steel 1000°F (537°C) Turn count of 1/8 turn after finger-tight
Copper 400°F (204°C) Unplated; no side-load retainer style; 1/4 turn

Ratings belong to the named manufacturer’s parts and do not transfer to any other gasket.

Our own gasket is simpler to describe. The UHP gasket page lists 316 stainless steel, a corrosion-resistant alloy, in five head sizes: 1/8, 1/4, 1/2, 3/4 and 1 inch. The finish is listed as polished on three models and smooth machined on two. The page gives no plating, temperature or pressure figures, so ask for those before you design around them. Superlok® fittings have the finest interior surface finish of any tube and pipe fitting on the market, and a smooth finish matters at a sealing face as much as in the bore. Grade and rating are confirmed per order, with a sample material test report available. For the grade question, see 316 vs 316L.

Why the Gasket Is Replaced When the Joint Is Opened

The working rule is to fit a new gasket every time the joint is made up again. Be clear about what that rests on. Swagelok® describes the seal as the metal gasket compressed from both ends as the nut is tightened, so the first make-up deforms the gasket to the sealing faces. The Fluid Sealing Association handbook, a trade association publication from 2001, says of a different gasket, the BX ring joint type, that it is not recommended for re-use because it is coined into the groove. The principle is the same, but the gasket is not.

What the documents I checked do not state is a reuse limit for a face seal gasket. Swagelok®’s catalog and installer’s guide give turn counts but no reuse rule, and the Superlok® gasket page has none either. So treat the new-gasket rule as engineering practice, and check it against your site procedure. A Stanford physics laboratory’s practices page, dated 12 November 2020, adds that assembling these fittings without a gasket damages them. Never do it.

Retainer Gaskets and When to Use Them

A retainer keeps the gasket with the gland. Swagelok® says its side-load retainer gasket allows easy installation and minimal clearance for removal, and states that its retainer and gasket must be used as an assembly, that nickel and copper retainer assemblies use a 316 stainless steel retainer, and that side-load retainer gaskets are not available in copper. It also lists some items as not designed for a retainer assembly, so check the part before you order one.

The Superlok® UHP gasket retainer assembly page lists 316 stainless steel in four head sizes, 1/4, 1/2, 3/4 and 1 inch. The gasket page also lists 1/8 inch, so there is no retainer assembly listed at that size. The same page describes the part as designed to secure gaskets in clean high-purity systems and lists no compatible gasket materials. Confirm the pairing when you quote. The retainer is not an extra seal; it sits beside the gasket and is replaced with it.

Turns, Not Torque: Making Up the Joint

Face seal joints are made up by turns from finger-tight, not by a torque value. Swagelok®’s catalog gives 1/8 turn for stainless steel and nickel gaskets and 1/4 turn for copper, with no figure by size and no torque value. The Stanford page recommends tightening by hand first. I could not find a face seal torque in the Superlok® pages I checked, and the installation guide covers tube fittings, not metal gasket joints, so request the instruction for your part before the crew starts.

One cleaning point from the Swagelok® documents: its female nuts are silver plated, and it warns against chemical cleaning, electropolishing and passivation that remove the plating, because damaged plating can cause thread galling. Check what your process does to any plated part. The wider build context is in semiconductor fab fittings.

Leak Testing the Joint

A new gasket proves nothing until the joint is tested. Swagelok® states that its VCR® design was helium leak tested to a maximum of 4 x 10-9 std cm3/s with silver-plated and copper gaskets and 4 x 10-11 std cm3/s with unplated gaskets. The gap is a factor of 100, by arithmetic. It shows that plating changes the number, so state which gasket a leak specification assumes. No leak rate is claimed here for a Superlok® gasket. If your joint seals with an elastomer instead, you want O-ring face seal fittings.

Questions on Gasket Fit and Reuse

Can I reuse a gasket if it looks undamaged?

The sources give no reuse limit, so follow your site procedure and default to a new gasket. Appearance alone does not show whether a gasket has already deformed.

Which gasket material for a stainless steel line?

Match the line and the temperature. Our listed gasket is 316 stainless steel; nickel and plated options are described above for another maker, not for our parts.

Do I need a retainer?

Only if the joint design or access calls for one, and the retainer and gasket are fitted as a pair.

What torque do I use?

Published face seal instructions use turns from finger-tight. Ask us for the instruction for your size.

Confirm gasket and retainer before the order

Send the gland size and the material you want listed, and we will check the gasket and retainer pairing for you.

Request a Quote →

SUPERLOK NORTH AMERICA

One small part holds the seal; fit it new, turn it once and test it.

Sources

  1. Swagelok® Company, VCR® Metal Gasket Face Seal Fittings catalog, MS-01-24, Rev X, September 2026. Manufacturer publication. Supports gasket materials, stated maximum temperatures, the 1/8 and 1/4 turn counts, retainer notes, the absence of torque values and reuse guidance, and the helium leak rates. swagelok.com
  2. Swagelok® Company, An Installer’s Pocket Guide for VCR® Metal Gasket Face Seal Fittings and Micro-Fit® Weld Fittings, MS-13-150, Rev F, May 2022. Manufacturer publication. Supports the turn counts, the retainer notes, the silver-plated nuts and plating warning, and the absence of a reuse rule. swagelok.com
  3. Swagelok® Company, VCR® Metal Gasket Face Seal Fittings product category page. Manufacturer publication. Supports the description of the gasket compressed from both ends on tightening. products.swagelok.com
  4. Swagelok® Company, product page for a 1/4 in. nickel VCR® gasket (NI-4-VCR-2-GR). Manufacturer publication. Supports the nickel body and silver-plated listing. products.swagelok.com
  5. Fluid Sealing Association, Metallic Gasket Handbook, 2001. Trade association publication. Supports the statement that BX ring joint gaskets are not recommended for re-use. fluidsealing.com
  6. Gratta Labs, Physics Department, Stanford University, "Good laboratory practices," 12 November 2020. Supports the warnings about assembly without a gasket and the advice to tighten by hand first. web.stanford.edu
  7. Superlok North America, UHP gasket product page. Manufacturer publication. Supports 316 stainless steel, the five head sizes and the finish listing. superloknorthamerica.com
  8. Superlok North America, UHP gasket retainer assembly product page. Manufacturer publication. Supports 316 stainless steel, four head sizes and the description of the part. superloknorthamerica.com

Technical note: These sources establish what Swagelok® publishes for its own VCR® gaskets, what the two Superlok® product pages list, and one trade association statement about a different gasket type. They do not establish a reuse limit, a torque value or a leak rate for any Superlok® gasket, and they do not show that the Swagelok® figures apply to other makers. The new-gasket rule is engineering practice, not a quoted requirement. Material grade and rating are confirmed per order.

Trademark disclaimer: Superlok® is a registered mark of its owner. Swagelok®, VCR® and Micro-Fit® are registered marks of Swagelok® Company, named only to identify the manufacturer and the documents cited; no Superlok® part is described as a VCR® part. The Fluid Sealing Association and Stanford University are named only as sources. Cross-references are made by form, fit, and function only.